SPINDLE TYPE A ) Spindle covered of polyamide with the internal part available in Steel Available in M16 base diameter 63, 100, 110, 125. Ideal for small load utilisation.

SPINDLE TYPE B ) Spindle available in Stainless Steel or Zinc plated steel. Manufactured in on piece. Available in M8, M10, M12, M14, M16, M20, M24 for base diameter 40, 50, 60SS, 63, 80, 80SS, 100, 100SS, 110, 125. Length according to table.

SPINDLE TYPE J ) Polyamide Spindle available in M16 for bases diameter 63, 100, 110, 125.
Highly recommended in applications with low weight requirements.

SPINDLE TYPE P ) Spindle available in Stainless Steel or Zinc plated steel with hexagonal base. Manufactured in on piece. Available in M16 o M20 for articulated feet diameter 130. Length according to table. Ideal for heavy load utilization and light inclination requirement.

SPINDLE TYPE Q ) Spindle ava ilable in Stainless Steel or Zinc plated steel. Manufactured in on piece. Available in M24 o M30 for articulated feet diameter 130. Length according to table. Ideal for heavy load utilization and light inclination requirement.

SPINDLE TYPE R ) Spindle available in Stainless Steel or Zinc plated steel with hexagonal base. Manufactured in on piece. Available in M16 o M20 for fixed feet diameter 130. Length according to table Ideal for heavy loads.

SPINDLE TYPE S ) Spindle available in stainless steel or Zinc plated steel. Single piece manufacurated procces. Available in M24 o M30 for fixed feets diameter 130. Lenght according table. Ideal for heavy loads.

  
   
 
 
 

 

LOW FRICTION ACETAL (LF)
This is a thermoplastic material with special additives providing low friction coefficients and high tensile strength. This material's specific components make ideally suited for use in places where lubrication is impossible, particularly in curved-route chains. Material with certificate FDA.
 

ACETAL  (D)
This thermoplastic has extremely good mechanical properties. It is used without any special additives in conventional conveyors. Material with certificate FDA.
 

WHITE ACETAL (AW)
Thermoplastics with good mechanical propierties, ideal used for food conveyors belts. Material with certificate FDA.
 

REINFORCED POLYPROPYLENE (PP + FV).
Fibre-glass reinforced polypropylene. This material is highly resistant to chemical agents.
 

POLYAMIDA
This material has high tenacity and good noises absorption polyamide.
 

REINFORCED POLYAMIDE
Polyamide variant with mechanical and thermal properties inproved
 

POLYETHYLENE UHMW-PE - DESLIDUR
The ultra high molecular weight polyethylene is the material more used in friction applications in view of his peice-quality relation. it can be used in sliding guides as with idhler wheels, that can even work directly over the axis (for more information see the DESLIDUR catalogue) Material with certificate FDA.
 








 

 

TREATED STEEL (S)
Carbon treated steel provides extreme surface hardness. Commonly used in conveyors for the engineering industry.
 

AISI 430 (SS)
Din 1.4016 - Magnetic grade, 17% Cr. Hardened by cold rolling to a hardness of 850 N/MM. Used in the majority of bottling plants. It is the most economical of the stainless steels. Also for nuts AISI304.
 

AISI 304 (SSS)
DIN 1.4301 - Austenitic steel 18/8 - CRNI Chrome nickel. Cold rolled to 28 HRC. Makes it possible to combine high tensile strength with a high elastic limit. Non-magnetic. The most commonly used material in the food industry, even where the product is in direct contact with the chain.
 

SÚPER TENAZ (SSC)
A magnetic stainless steel alloy. Chrome nickel magnesium. Cold rolled to 30 HRC. Specially suitable for high speed and high performance lines. 
 

SS302
A type of stainless steel specially developed for use in all stainless steel chain pins. Hardnesses of over 1400 N/MM.
 

SS420
Stainless steel variant using hardened treatment to achieve superior resistance. It resistance limit is 41 – 44 HRC
 

SS316
Stainless steel variant with superior acid resistance. Used in somme of our chains in polypropylene + glass fiber.
 

SS304
Stainless steel variant hardened using rolling coil to improve thermoplatic chains weariness up to 1100 N/mm2 resistance
 

SS303
Stainless steel variant used in spindle feet manufacturing process. Showcase superior load resistance.

  

Our constantly developing engineering departament, in collaboration with the leading raw materials spplierts, offers our clients the possibility of specific solutions to suit their particular application needs. 
• Antistatic material. 
• High temperatures. 
• Ultraviolet ray resistant.







 

 
 

MINIMUM TEMPERATURE

MAXIMUM TEMPERATURE

Dry enviroment

Wet environement
Acetal LF
Acetal D
Reinforced Polypropylene (PP+FV)
Polyamida
Reinforced Polyamida
Polyethylene UHMW-PE DESLIDUR
Stainless Steel  SSC
Stainless Steel  304 (SSS)
Treated Steel 

-40
-40
+5
-5
-10
-40
-40
-40
-40

+85
+85
+105
+80
+120
+80
260
+400
+180

+70
+70
+105
+90
+120
+70
+120
+120
+120







 

 

NEWTONS
400

AW

 6500
450 AW 1500
515 SSS 10400
550 LF 6500
600 AW 8000
610 AW 8000
805 SSS
SSC		 19000
19000
810 SSS
SSC		 4500
4500
815 SSS
SSC		 10200
10400
820 LF 3200
821 LF 6500
880 LF 5200
880R LF 4500
881 SSS
SSC		 10000
9500
882 LF 8000
900 D 4000
1700 AW 6500
9000 LF/PP 4500
9100 LF/PP 4500


 
 
 
 
 
 

 

NEWTONS
400
450
515
550
610
805
810
815**
820
821
843
863
900
880
881
882
1843
1873
1873G		 300
150
75
50
50
150
75
150
40
40
90
125
0
40
50
40
75
300
150

 




 ** Back bend radius of 75 mm available on request.


 
 
 
 
 
 

  

 

W
400
500
515
600
610
805
810
815
820
821
843
863
880
881
882
1873		 7,80
-12,00
3,90
-18,50
-14,00
3,90
3,90
3,90
3,90
3,90
5,95
10,30
4,00
3,90
5,00
9,50		 35
50
25
65
65
38
38
38
38
38
25
38
38
38
38
38







 

  
DRIVE SPROCKET

DF

A1

K

SPLIT DRIVE SPROCKET

DF

A1

K

IDLER WHEEL

DF